How do you troubleshoot a DSC alarm system?

How do you troubleshoot a DSC alarm system?

How to Troubleshoot Problems on the DSC Home Security System

1. Press the pound key (#) to stop the security system from repeatedly beeping.
2. Press the star key (*) and then press the number 2 key.
3. Change the battery per the panel’s instruction manual if a number 1 appears on the display or the 1 zone is illuminated.

How do I reset my DSC trouble light?

DSC alarms can go off for a number of reasons. To reset the alarm or the warning lights, enter your master code twice, press the reset button, and then enter “*72” if the alarm is still ringing. Once the alarm is off, try to find out why it went off.

How do I reset my home alarm without the code?

How to reset a house alarm without a code or you’ve lost it?

1. Go to your alarm system’s main access panel.
2. Remove the power plug to the alarm console from the socket.
3. Unlock and open the main panel with the console access key, or a small tool, such as a screw.
4. Disconnect one of the wires from the system’s main battery.

How do I reset my DSC alarm after a power outage?

How to Reset a DSC Alarm After the Power Has Been Off

1. Open the access door on the unit.
2. Press and hold the “RESET” key for 2 seconds.
3. Press the buttons “*72” if the alarm does not reset after pressing the RESET button.
4. Check the sensors if it still does not turn off.

How do I bypass zone on DSC 1616?

How to Bypass a Zone on a DSC Power Series Security Alarm Panel

1. The System Must be disarmed prior to proceeding.
2. Press the * Key.
3. Press the 1 Key.
4. Use the > key to scroll to the zone you wish to bypass.
5. Press the * Key on the appropriate zone.
6. A “B” should appear next to the zone when the system is bypassed.

How do you reprogram a house alarm?

How to reset a house alarm after a power cut?

1. Locate the “System” or “System Status” button. On your home alarm keypad, find the “System” or “System Status” button.
2. Open the control panel.
3. Remove the backup battery.
4. Switch the circuit breaker off and on.
5. Replace the backup battery.
6. Input your user code.

How do you reset your house alarm after a power cut?

Start by inserting the back-up batteries into the system. Then plug the main control panel back in. Alternatively, if you had to turn off the power to shut off a hardwired system, go back to your circuit breaker and flip the appropriate switch.

How do I get my alarm to stop beeping after power outage?

Go to your main control box and disconnect the battery supply, which will stop all beeping and shut your alarm system down. Once power is restored, you can reconnect your battery and your alarm system should work as before.

How can I tell if my DSC power series is in trouble?

To view a trouble condition, press [*] [2]. The trouble light will flash and the LCD will display the first trouble condition present. Use the arrow keys to scroll through all trouble conditions present. Note: When additional information is available for a specific trouble condition a [*] will appear on the display.

What causes a problem on a DSc keypad?

From time to time, conditions may arise which cause what is known as a ‘trouble’ condition on the keypad. Trouble conditions are wide ranging and can be anything from a low battery to a power failure to a communications failure.

How to fix module supervision trouble condition on a DSc 1616, 1832 or 1864?

How do I fix a module supervision trouble condition on a DSC 1616, 1832, or 1864? I’m not using a telephone line, how do I turn off telephone line monitoring on the DSC 1616, 1832, and 1864?

How to troubleshoot DSC power series bulwark battery?

The PC5204 battery is below 11.5 VDC. The trouble condition will not clear until the battery is at least 12.5VDC under load. If the battery is new, allow 1 hour for the battery to charge. Ensure the module is getting proper AC power. Measure across the two AC terminals of the module and ensure the AC input is between 16 and 18VAC.

How do you troubleshoot a DSC alarm system? How to Troubleshoot Problems on the DSC Home Security System Press the pound key (#) to stop the security system from repeatedly beeping. Press the star key (*) and then press the number 2 key. Change the battery per the panel’s instruction manual if a number 1…